Removable Rear Cupholder for VW ID.4 (2023–2026 US/Canada)

Give Your Rear Passengers a Proper Place for Their Drinks

Add convenient rear cupholders to your 2023–2026 US/Canadian Volkswagen ID.4 without drilling, tools or permanent modification.

The YURIK Removable Rear Cupholder fits into the rear center-console area, giving passengers a convenient place for drinks while keeping the vehicle's rear USB-C ports accessible.

When you don't need the cupholder, simply remove it.

Why You'll Like It

• Adds rear cupholders — convenient drink storage for back-seat passengers
• Designed specifically for the VW ID.4 — made around the 2023–2026 North American rear-console configuration
• Secure clip-on fit — inserts into the existing cubby and clips onto its lower lip
• Completely removable — take it out whenever you want the original storage space back
• No tools or adhesive — no drilling, screws or permanent modification
• Keeps USB-C ports accessible — rear passengers can continue using the charging ports
• PETG construction — 3D printed for everyday interior use
• Clean, integrated appearance — designed around the ID.4 interior
  
• Made in the EU — designed and 3D printed by YURIK Accessories

Designed Around the ID.4 Rear Console

Rather than permanently attaching a cupholder to the interior, this design makes use of the existing storage cubby below the rear air vents.

The cupholder inserts into the cubby and clips onto its lower lip, helping to hold the unit securely in position without screws, adhesive or modifications to the vehicle.

The design also preserves access to the rear USB-C charging ports.

Because the installation is completely removable, you can take the cupholder out whenever you want to use the original cubby space again.

Compatibility

Designed for:

Volkswagen ID.4 — US/Canadian models, 2023–2026

Important: This cupholder does not fit versions equipped with heated rear seats (Plus).

Please check your vehicle configuration before ordering.

Installation

1. No tools, drilling or permanent modification are required.
2. Remove the rubber mat from the cubby
3. Position the cupholder at the rear center-console mounting area.
4. Insert it into the intended position until it clicks
5. Make sure the cupholder is fully seated and secure before use.
6. Remove it whenever the additional space is preferred.

The rear USB-C ports remain accessible with the cupholder installed.

Material & Manufacturing

The cupholder is 3D printed from PETG for everyday use inside the vehicle.

Material: PETG
Manufacturing method: 3D printing
Installation: Removable, tool-free
Designed by: YURIK Accessories
Manufactured in: European Union

Because this is a 3D-printed product, minor layer lines and other surface characteristics associated with the printing process may be visible. These are normal and do not affect the intended function of the product.

Important Information

Make sure the cupholder is correctly installed and secure before driving.

Use containers that fit securely in the cupholder. An improperly sized or unsecured container may tip or spill during acceleration, braking or cornering.

Do not overload the cupholder or use it if it is cracked, damaged, deformed or can no longer be securely positioned.

Remove any spilled liquid promptly and follow the vehicle manufacturer's recommendations for cleaning the surrounding interior and electronic/USB-C areas.

YURIK Accessories is an independent aftermarket-accessory manufacturer and is not affiliated with or endorsed by Volkswagen AG. Volkswagen and ID.4 are trademarks of their respective owners and are used solely to identify vehicle compatibility.

Most items are shipped within 2-7 days; however, sometimes we need a little bit more time to make and finish your order. We are not responsible for customs delays

This product is a non-electrical automotive accessory designed for vehicle interior or exterior use. It does not connect to the vehicle’s electrical system unless explicitly stated in the product description and contains no electronic components.

Intended Use:

Designed for use with the specific vehicle models listed on this product page to improve convenience, organization, or protection during normal vehicle operation or charging.

Material Information:

Manufactured using durable plastic materials (including PETG, PLA, and/or TPU), selected for automotive use.

• Safety Information:
• Not a toy. Keep out of reach of children.
• Do not use if damaged, cracked, or deformed.
• Ensure the product does not interfere with vehicle controls, sensors, airbags, or charging connectors.
• Remove the product if it affects safe vehicle operation.
• Always follow the vehicle manufacturer’s instructions.
  

Compatibility:

Compatible only with the vehicle models explicitly listed in the product description. Not suitable for other vehicles.

Manufacturer / Responsible Economic Operator (EU):

YURIK Accessories

Email: info@yurikaccessories.com

Buyers are responsible for any customs and import taxes that may apply. I'm not responsible for delays due to customs.

Yuri is a designer and maker based in the Netherlands who started YURIK Accessories in 2021 after spotting an unused space under the central console of his VW ID.4 — and deciding to do something about it. What began as a 3D-printed tray shared in an owner community has grown into a range of precision accessories shipped worldwide. Every product is designed and 3D-printed with the same hands-on attention to detail that started it all.